The 74HC; 74HCT is an 8-bit buffer/line driver with 3-state outputs. The device can be used as two 4-bit buffers or one 8-bit buffer. Buffers: vs is an octal unidirectional buffer. The 8 lines can be split into two groups and each group can be individually. Electrical Engineering Glossary of Electronic Terms, 8-Bit Buffer IC, functional schematic diagram, true table and package out-line. 74HCT

Author: Zugis Viktilar
Country: Poland
Language: English (Spanish)
Genre: Education
Published (Last): 15 June 2012
Pages: 205
PDF File Size: 1.4 Mb
ePub File Size: 6.38 Mb
ISBN: 394-8-78412-822-7
Downloads: 49921
Price: Free* [*Free Regsitration Required]
Uploader: Zulkinos

It does not invert or alter its input signal in any way. From Wikipedia, the free encyclopedia. Graphically, it is often represented as a triangle with a small circle attaching to the tip.

Glossary of Electronic and Engineering Terms, IC 8-Bit Buffer Description

Note that the chip displayed indicates OE control of the output [Output Enable]. The location of the bypass capacitor is extremely important; read more on Capacitor Placementas it applies to IC by-passing.

A control input is analogous to a valve, which controls the data flow. When the control input is active, the output value is the input value, and the buffer is not different from the single input digital buffer. Finally, note that the manufacturer is not listed 7424 either. In this case, the input data is sent to the output. Because the resistance is infinity, the circuit will draw very little current, and will not disturb the original circuit. Views Read Edit View history. This kind of buffer performs no inversion or decision-making possibilities.

Although one may cost more that the other, but a small price to pay for time to market.


Buffers: vs – Geek went Freak!

Also refer to Logic Family vs Switching Speed. A Tri-state buffer, with its control input, can prevent a bus from reading excessive input.

A bus can only read one data input from a device at one time, and that is when a tri-state buffer is applied. However what is available in the IC family may also come into play. Retrieved from ” https: The point of this list is to indicate that a government agency could attempt to procure these items based on the VID number provided. A voltage buffer has a very high input impedance the opposition to current flow viewed from the load.

By using this site, you agree to the Terms of Use and Privacy Policy. The output value will be high if and only if the input value is high. A single input digital buffer is different from an inverter.

The high input impedance is the reason a voltage buffer is used. As a result, the power source will not be affected.

If the input is high, the output is low and vice versa. The output value will be 742444 and current will flow through the element. The digital buffer is important because it can control the on and off of data transmission, which is used widely in the world of registers sophisticated data storage device and buses data transferring device.

Electronic Engineering Glossary Terms

This page was last edited on 19 Septemberat Both data input and control input is active. The output value is 0, which means no current.

Add a second by-pass capacitor, and place both by-pass capacitors as close to the Vcc line as possible. Ubffer type or family of buffer used bfufer make a difference in the table above, just the trailing digits that indicate the type of buffer [as in the different options]. Using just the standard. Tri-state voltage buffers are used widely on buseswhich allows multiple devices communicate with each other.


A digital buffer serves to transfer a voltage from a circuit that has a high output impedance level, to a second circuit with a low input impedance level. Other than size, Lead Inductance is the next important issue because it slows down switching time, while the size of the IC package causes the placement of the capacitor to move away from the power leads of the IC. A typical digital buffer that is used to control multiple data inputs written onto a bus is a Tri-State Digital Buffer, which controls the data flow by “tri-state” pins.

The suffix is used to define the package style [which is listed] and the packaging method during shipping [which is a don’t care]. Pick a series [54x] if need the temperature range, bufferr use the series [74x]. Although we allow the data transmission by turning on the control input, we don’t have data coming in because of the infinite resistance. Both the data and the control input are inactive; the buffer shuts down.

As a result, huge amounts of power is drawn by the power source, which causes high disturbances. A circuit with a voltage buffer will bufcer draw a little amount of current because of the high input impedance of the buffer.