Europastandarden EN gäller som svensk standard. The European Standard EN has the status of a Swedish. Standards. DIN EN Safety of industrial trucks – Pedestrian propelled manual and semi-manual trucks – Part 3: Platform trucks; German version EN. DIN EN Safety of industrial trucks – Pedestrian propelled manual and semi-manual trucks – Part 3: Platform trucks.
|Published (Last):||1 December 2018|
|PDF File Size:||4.52 Mb|
|ePub File Size:||12.10 Mb|
|Price:||Free* [*Free Regsitration Required]|
BS EN 1757-3:2002
In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, 177-3 otherwise requested. Please download Chrome or Firefox or view our browser tips. The hand grips shall be of a cross section enclosed within the space between two concentric circles of 25 mm inside diameter and 35 mm outside diameter.
The force shall be applied horizontally along the truck’s axis on the tiller handle or bar. This series of standards includes: The same test shall be carried out when pulling. The test load, where applicable, shall be applied according to clause 3. The test shall be carried out with a new truck chosen according to 6. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it 17557-3 amendment or revision.
It is the constant aim of BSI to improve the quality of our products and services. Handbetriebene und teilweise handbetriebene Flurfoerderzeuge. The frequency of the load handling cycle should also be taken into account. It presents the UK view on standards in Europe and at the international level. The centre of gravity of the load on each level shall be on the centre line of the truck and mm above the geometrical centre of the platform or the e 3.
The maximum steering force EBmax is the average of the recorded measurements on the left hand side G and on the right hand side D.
BS EN – Safety of industrial trucks. Pedestrian propelled trucks. Platform trucks
Loading and unloading may be manual or by external mechanical means 3. During measurement the lower surface of the tiller handle shall be 1577-3 at a height of mm above the ground.
Chariots a plateau fixe. This website is best viewed with browser version of up to Microsoft Internet Explorer 8 or Firefox 3. Date Comments Li ce ns ed c op y: With the truck stationary, measurement consists of recording the maximum 7157-3 applied tangentially in the middle of the handle throughout the steering lock in one direction from the tiller’s axial position Figure A.
Users are responsible for its correct application.
1757–3 Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Search all products by. Tests shall either be performed by operating the truck in the manner prescribed below or, where practicable, be simulated by any method giving an equivalent effect and producing substantially the same results.
Additional requirements for trucks with elevating operator position and trucks specifically designed to travel with elevated loads EN Safety of industrial trucks – Operation in potentially hazardous atmospheres — Use in inflammable gas, vapour, mist and dust EN Safety of industrial trucks – Pedestrian propelled trucks Part 1: ENRoll containers.
Up-to-date e and bibliographical references concerning such national standards may be eh on application to the Management Centre or to any CEN member.
If these details are to be used for any other purpose than implementation then the prior written permission e BSI must be obtained. The machinery concerned and the extent to which hazards, hazardous situations and events are covered are indicated in the scope of this document. In case of incorrect operation, the truck shall be adapted until the test is successful. Learn more about the cookies 177-3 use and how to change your settings.
This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. The tiller shall be maintained in vertical position along the truck’s axis. The corresponding requirements are designed to limit the risk or reduce these 1757- in each situation. It is incorporated by Royal Charter.
The rated capacity shall be easily readable by the operator.
BS EN Safety of industrial trucks – MBA智库文档
It may occasionally be necessary to negotiate small slopes for the purposes of moving the truck between buildings etc. This publication does not purport to include all the necessary provisions of a contract. BS EN Safety of industrial trucks.
The maximum starting force EDmax or the maximum rolling force ERmax is the average of the maximum values recorded in each direction of travel, forward AV and reverse AR, during two successive tests.
General wn Part 2: The faster, easier way to work with standards. NOTE The forces to operate the truck are varying with the value of the load, the ground conditions and the truck conditions. Stacker trucks Part 2: You may find similar items within these categories by selecting from the choices below:.
NBN EN 1757-3
Platform trucks Part 4: Industrial trucks, Materials handling equipment, Hand trucks, Equipment safety, 17577-3 engineering, Commercial road vehicles, Pedestrian-controlled systems, Platforms, Hazards. Your basket is empty. BS EN Safety of industrial trucks — Self-propelled trucks up to and including 10 kg capacity and industrial tractors with a drawbar pull up.
Contact the Information Centre.